register free | resend password

Family

Themenbereich / / Family


Sortiere PresseMitteilungen nach: Titel (A\D) Datum (A\D)

Seiten sind aktuell sortiert nach: Datum (erst neue PresseMitteilungen)

Wide choice of custom options for new Hall Effect angle sensor range: Variohm EuroSensor launch new miniature rotary shaft programmable angle sensor

Variohm EuroSensor?s new Euro-CMRS series miniature angle sensors offer programmable angles from 30? to 360? in 1? increments in a non-contacting and long-life Hall Effect design that includes a durable IP68sealed aluminium housing with 18 mm PCD mounting and a micro 4 mm diameter 316 stainless steel D-type shaft. Output options - from an industry standard 5 VDC input - cover CW or CCW direction with single or dual redundant angle measurement at ratiometric or PWM signal levels. With mechanical and electrical manufacturing flexibility designed-in, the Euro-CMRS can easily accommodate customise ...

24.05.2019

Delta to Demonstrate Smart Manufacturing Solutions at SPS IPC Drives Italia 2019

Delta, a global provider of smart and energy-efficient industrial automation solutions, today announced it will be demonstrating several smart manufacturing solutions at SPS IPC Drives Italia 2019. The highlight of Delta?s exhibition at the show will be a demonstration of the new CODESYS-based Motion Control Solution, which integrates the control layers of PLCs, HMIs, and motion controllers into one single platform to provide seamless control of a Delta SCARA robot on site. Also on display will be Delta?s DIAEnergie solution, which offers factories and production lines the possibility to enhan ...

23.05.2019

MDR - an overview

. Introduction The MDR (Medical Device Regulation) is currently a hot topic and is keeping manufacturers of medical products and their suppliers on their toes. There are many different reasons for this. On one hand, the timeline laid out by the EU is extremely ambitious and, on the other, it is not yet clear how much of what is detailed in the regulation will be implemented in practice. What is the MDR? The new European MDR replaces the existing MDD (Medical Device Directive) and AIMD (Active Implantable Medical Devices), which will now be combined in the MDR in future. The advantage of the re ...

23.05.2019

New cleaning solutions for altered requirements

Coating, adhesive bonding, sealing, painting ? these are just some manufacturing operations calling for profoundly clean, and sometimes activated, part surfaces. It is with these requirements in mind that Ecoclean has developed a set of new cleaning solutions. One of them combines wet chemical and low-pressure plasma cleaning in a single machine. Another innovation consists in integrating diverse applications for partial or full-surface cleaning or activation ? e.g., atmospheric pressure plasma treatment, laser, CO2 snow blasting and/or surface inspection operations ? into one processing syste ...

23.05.2019

Advantages and benefits of OPC UA in the plastics industry

For years now, the world has been talking about ?Industry 4.0?. The exchange of data in production plays an important role in making the introduction of Industry 4.0 a success. The open communication protocol OPC Unified Architecture, or OPC UA, is increasingly gaining popularity as a way of promoting data sharing. But what advantages and benefits does using OPC UA offer the plastics industry, for example? In the plastics industry, the OPC UA machine communication standard helps to optimise processes from production to service while minimising the loss of time, resources and products (rejects) ...

20.05.2019

HERBOLD Meckesheim has just started rebuilding the site destroyed by the devastating blaze

After the devastating fire in September 2019, HERBOLD Meckesheim has just begun rebuilding the destroyed production halls. The whole incoming goods and shipping department, the warehouse as well as parts of the production area were devastated by the flames. The new buildings comprise a 4000 M2-area and are supposed to be up and running in September 2019. As the General Manager Werner Herbold put it: ?This was the perfect opportunity to reorganize our business activities in order to be more flexible in all our steps and at the same time relieve the traffic situation in the neighbourhood. We are ...

15.05.2019

Endress+Hauser grows significantly

Endress+Hauser experienced strong growth across all regions, sectors and product areas in 2018. The ongoing digitalization of the industry and positive development on the international markets provided impetus. The Group increased sales and profits, invested heavily and created hundreds of jobs worldwide. ?The bottom line is, 2018 was a good year for Endress+Hauser worldwide,? explained CEO Matthias Altendorf at the Group?s annual media conference in Basel. The Group increased net sales by 9.5 US moves to number one The business was bolstered by a strong economy in the process automation secto ...

14.05.2019

Servo couplings for bridging larger distances without an intermediate bearing support

As well as servo bellow couplings as standard and miniature couplings and couplings for fitting in tight spaces or with high torques, JAKOB also manufactures servo couplings for long wheelbases of up to 6 m. These distance couplings, also referred to as prop shafts or intermediate axes, are used to bridge large shaft distances without intermediate bearings. Highly-dynamic distance couplings are needed everywhere in machine and plant construction. They are used primarily in connection with jack screw gears, linear guides, palletting and packaging systems. The main design feature of the distance ...

13.05.2019

On-site service from dedicated PU experts: New exclusive Hennecke GROUP sales agent for the UK and Ireland

Due to the GROUP?s steady growth and the integration of HENNECKE-OMS (former ?Impianti OMS?) at the end of 2017, Hennecke has restructured parts of its external organization and worldwide agency network. On 1st April 2019 CTM UK Ltd. became the exclusive agent for the entire Hennecke GROUP product range in the UK and Ireland and is now offering a comprehensive range of services that focuses on the machine and systems technology portfolio of both core brands, Hennecke Polyurethane Technology and HENNECKE-OMS. CTM UK Ltd. is located in northern England in the town of Barnsley, South Yorkshire. T ...

13.05.2019

Exciting Control Show with Numerous Novelties from Yxlon

At this year''s Control in Stuttgart, Yxlon presented innovations for both the classic NDT and manufacturing electronics sectors. In live presentations of the YXLON FF35 CT system, the new release of the Geminy-based, high-resolution computed tomography system family was presented. In addition, a brand-new ADR function (Automatic Defect Recognition) on the YXLON Cheetah EVO Plus microfocus X-ray system was demonstrated, which is intended to ensure reliable test results and greater efficiency, particularly in the electronics sector. Many innovations and advancements in the new release ...

10.05.2019

The vast world of additive manufacturing and new approaches for use in investment casting

Who would have thought 20 years ago that it is possible to print components? The possibilities of additive production continue to grow and pose new challenges for BLANK regarding the investment casting process. "It is important to keep up with the times and test out innovations on the market," says the head of the Mould Construction Division at BLANK, "The creation of a tool is at the beginning of the manufacturing process of an investment casting part, and also here potential is already being exploited by the additive production methods. At the end of 2017 for example, the firs ...

10.05.2019

Electric cars: Optimal temperature with Combicore

The optimum operating temperature of a component determines its efficiency and service life. For example, the range of electric cars drops rapidly in colder temperatures, sometimes by up to 50 percent. There are also problems with charging the batteries. On the other hand, if it is too hot, batteries age faster. Combicore casting cores efficiently keep sensitive components at temperature. The channels cast with Combicore safely conduct water or chemical coolants through the component to where it needs to do its job. If the coolant is very close to the individual battery cell, optimum heat tran ...

09.05.2019

Combicore cores revolutionize die casting and other casting processes

Undercuts are hardly possible in high pressure die casting. New technologies require new cooling concepts and a consequent lightweight construction. In high pressure die casting ducts for cooling or oil are traditionally realized by sliders or drilling afterwards. However, such cavities are bound to straight axes. Sand cores that are known from other casting processes are not applicable due to the high load. With the innovative and highly stable Combicore solution, casting cores can also be applied in high pressure die casting for the first time. Even with a high casting pressure level above 1 ...

09.05.2019

All-round hygienic solutions for the meat industry

In the food industry, production plants must be designed with hygienic aspects in mind. Depending on the hygiene zone, the requirements of the splash, packaging and non-food zones vary widely. At the IFFA, the leading international trade fair for the meat industry, Rittal will be presenting system solutions for enclosure, power distribution and climate control technology that are universally suitable, through to solutions for efficient engineering. The trade fair is Food manufacturers? production facilities must be as easy as possible to clean and at the same time so good (process-safe) that ...

08.05.2019

Extruder screws in the fast lane

ROWA Masterbatch and ROMIRA are equally renowned as industry specialists for the highest quality standards and products tailored to the customer. A common, technical core competence of the companies is less well known: The extruder screw facility (the Schneckenhaus) in which the pairs of extruder shafts are stored. The spaces of the extruder screw facility are designed so that the experts from ROWA Masterbatch and ROMIRA have fast access to the extruder screw shafts and extruder screw components, allowing defective parts to be quickly replaced or changes made to the extruder screw configuratio ...

08.05.2019

New monoflange design also prevents fugitive emissions

Compact design and minimised leakage potential: The new WIKA model IVM monoflange for connecting pressure measuring instruments to the process is particularly suitable for applications involving critical liquids, gases and vapours. Special seals also prevent fugitive emissions in accordance with TA-Luft (VDI 2440) and ISO 15848-1. The monoflange is manufactured and tested to comply with various common standards such as ASME BPVC. It is designed for a long service life, even under difficult conditions. The valves work durably, smoothly and precisely, even at high pressures. The metal seat of th ...

07.05.2019

Short installation times for switch cabinet manufacturers

Sonderhoff Italia, part of Henkel AG & Co. KGaA, will present its range of products and services at the international trade fair LAMIERA for the sheet metal processing industry in Milan, from May 15 to 18, 2019. This time, the focus will be on the new 3E dosing cell, the entry-level model for standard applications, the fast-curing Fast-Cure sealing foams for short installation times and the self-adhesive Geko-Spider polyurethane foam seal. In addition, with the SYSTEM3 concept, the company offers its customers the advantage of being able to purchase foam seals, adhesives and potting as wel ...

23.04.2019

Short and good

The coupling series KP with 4-corrugated bellows and two radial clamping hubs, is a version with shorter overall length in the JAKOB metal bellows coupling range. This makes it particularly suitable for applications with minimal shaft spacing and limited installation conditions. In addition, the very high torsional rigidity values ??and the easy-to-install clamping hub design are worth mentioning. A low moment of inertia and good values ??for the permissible shaft misalignments and restoring forces complete the positive picture. The multi-layer, made of certified stainless steel, metal bellows ...

23.04.2019

Economically shot blasting of castings

The surface treatment of castings has a decisive influence on the quality of the final products. At the fair GIFA which takes place in D Special features bring decisive advantages to the operator. The brackets of the steel mill tumble belt are designed to be particularly wear-resistant. The change intervals extend significantly. The ventilation of the blasting chamber has been designed in a special manner which ensures that the workpieces leave it dust-free immediately after blasting. In this way, the cycle time can be shortened. A longer air outlet is avoided after the blasting process. In ad ...

23.04.2019

High-Performance Polymers in the Production of Food

BIEGLO ? High Performance Polymers has several high-temperature plastics in their portfolio that are suitable for the application in the food industry. Especially the program of PEEK granules, compounds, and semi-finished goods are all certified according to FDA and EU 10/2011. PEEK is extremely resistant against sour and alkalic cleaning supplies, as well as against steam. A popular use is also CIP-cleaning. The self-lubricating PEEK can also be used to produce bearings, assembly lines, gears and bushings. Moreover, through coatings the friction and wear can be notably reduced. Through specif ...

18.04.2019


Page 1 from 416:  1 2  3  4  5  .. » 416





All members: 9 213
Register today: 0
Register yesterday: 1
Members online: 0
Guests online: 50


Don't have an account yet? You can create one. As registered user you have some advantages like theme manager, comments configuration and post comments with your name.

Categories:


[ more PressReleases ][ RSS-Feed ]